1. Electroplating process control
Take 20cm galvanized wire for acid fog experiment, check the zinc content of galvanized wire through the balance to see whether it meets the zinc layer standard required by customers, ensure that the metal wire achieves the role of rust and corrosion prevention, and meet the service life required by customers. Galvanized iron wires must be packed in good condition, bound neatly and orderly, and bound inward to prevent scratches during transportation. The inspection standard of galvanized iron wire also includes the tensile test, which is decided according to the material of the galvanized wire order ordered by the customer, and it needs to be tested by comparing the raw material list.
4, according to the wire diameter thickness to adjust zinc dipping timeBecause of the large size of the barbed rope, the rope factory is used to packing. If you do not pack, then a load of blade rope can not hold many pieces, but also relatively occupy space and easy to be lost in the process of transportation.
The most obvious difference in a short time is the cross section of this piece, hot dip galvanized barbed wire because of surface anticorrosion treatment, so there will be rust in the cross section of this piece, and stainless steel barbed wire because the internal raw materials and surface raw materials are consistent, so there is no such situation.Zinc is a silver-white metal, brittle at room temperature, soluble in acid and alkali, known as amphoteric metal. Pure zinc is more stable in dry air, and small in humid air or water containing carbon dioxide and oxygen. A thin film layer of basic zinc carbonate will be formed on the surface, which can delay the corrosion rate of zinc layer. The corrosion resistance of galvanized layer in aqueous solution of acid, alkali and sodium chloride is relatively strong. It is also not resistant to corrosion in atmospheres containing carbon dioxide and hydrogen sulfide and in Marine atmospheres; In high temperature and high humidity air and containing organic acid atmosphere is small, galvanized layer is also easy to be corroded.
Friends in the industry know that galvanized iron wire has two kinds of cold galvanized iron wire and hot galvanized iron wire, so what is the difference between cold galvanized iron wire and hot galvanized iron wire? Which is good?
In our daily life, we are certainly familiar with the construction of power grid. Choosing such special barbed rope can improve the safety factor of the entire power grid during construction.
The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.
Steel mesh factory – improve the quality of reinforcement works. Electric welding wire mesh is produced by automatic intelligent production line under strict quality control in the factory. Strict control of mesh size, reinforcement specifications and quality. The omission of manual binding net is avoided, and the binding part is firm.
Because the coating obtained is thicker, hot-dip galvanizing has very good protective function than electric galvanizing, so it is an important maintenance coating for iron and steel parts in strict working environment. Hot-dip galvanized products are widely used in chemical equipment, petroleum processing, Marine exploration, metal structure, electric power transportation, shipbuilding and other occupations. In the field of agriculture, such as pesticide irrigation, greenhouse and construction industry such as water and gas transportation, wire casing, scaffolding, Bridges, highway guardrail and other aspects, it has been widely used in these years.
There is a good toughness and elasticity, in short, it can be easily made into a variety of shapes, and zinc as a coating is silver, very beautiful. This feature makes hot-dip galvanized wire handicrafts, wire mesh and other aspects are also used. Hot plating wire selection of high quality low carbon steel wire rod processing, is the selection of high quality low carbon steel, after drawing forming, pickling rust removal, high temperature annealing, cooling and other processes.The galvanized layer forms a special metallurgical structure that can withstand mechanical damage during transportation and use. Selection of low carbon raw materials, through wire drawing, annealing processing, soft and strong tensile resistance. Finished products coated with anti-rust oil, not easy to rust, according to customer requirements into bundles, each bundle of 1-50Kg, can also be made into U-shaped wire, broken wire, internal plastic and external hemp packaging, mainly used for binding silk, construction silk, etc.
There is good toughness and elasticity, simply put, can be easily made into various shapes, and zinc as a coating is silver, very beautiful. Such characteristics make hot dip galvanized wire handicrafts, woven screen and other aspects have also been applied. Hot plating wire selection of high quality low carbon steel rod processing, is the selection of high quality low carbon steel, after drawing molding, pickling rust removal, high temperature annealing, cooling and other processes.